1/2 www.rohm.com c 2012 rohm co., ltd. all rights reserved. 2012.05 - rev.b supply voltage input voltage output current storage temperature junction temperature power dissipation ? 120mw per element must not be exceeded. parameter symbol limits unit v cc 50 v v in 12 v ?5 i o 100 ma i c (max.) 100 ma tstg ?55~+150 c tj 150 c pd emh10,umh10n 150 (total) mw ? general purpose (dual digital transistors) emh10 / umh10n ? structure ? dimensions (unit : mm) epitaxial planar type npn silicon transistor (built-in resistor type) ? features 1) two dtc123j chips in a emt or umt package. 2) mounting possible with emt3 or umt3 automatic mounting machines. 3) transistor elements are independen t, eliminating interference. 4) mounting cost and area can be cut in half. ? packaging specifications umh10n emh10 type tn 3000 t2r 8000 ? ? package code basic ordering unit (pieces) taping ? absolute maximum ratings (ta=25 ?c) ? equivalent circuit ? electrical characteristics (ta=25 ?c) parameter symbol i i v i (off) v i (on) v o (on) i o (off) r 1 g i r 2 /r 1 min. ? 1.1 ? ? ? 1.54 80 17 ? ? 0.1 ? ? 2.2 ? 21 0.5 ? 0.3 3.6 0.5 2.86 ? 26 v v cc =5v, i o =100a v o =0.3v, i o =5ma i o /i i =5ma/0.25ma v i =5v v cc =50v, v i =0v ? v o =5v, i o =10ma v ma a k ? ?? typ. max. unit conditions f t ? 250 ? v ce =10v, i e = ?5ma, f=100mhz ? mhz input voltage output voltage input current output current input resistance dc current gain transition frequency resistance ratio ? transition frequency of the device rohm : emt6 emh10 rohm : umt6 eiaj : sc-88 umh10n abbreviated symbol : h10 abbreviated symbol : h10 each lead has same dimensions 0.22 1.2 1.6 ( 1 ) ( 2 ) ( 5 ) ( 3 ) ( 6 ) ( 4 ) 0.13 0.5 0.5 0.5 1.0 1.6 each lead has same dimensions 0to0.1 ( 6 ) 2.0 1.3 0.9 0.15 0.7 0.1min. 2.1 0.65 0.2 1.25 ( 1 ) 0.65 ( 4 ) ( 3 ) ( 2 ) ( 5 ) r 1 =2.2k r 2 =47k dtr 2 dtr 1 (3) (2) (1) (4) (5) (6) r 1 r 2 r 2 r 1 emh10 / umh10n
2/2 www.rohm.com c 2012 rohm co., ltd. all rights reserved. 2012.05 - rev.b data sheet emh10 / umh10n ? electrical characteristic curves input voltage : v i (on) (v) output current : i o (a) 100 200 500 1m 2m 5m 10m 20m 50m 100 m 100 50 20 10 5 2 1 500m 200m 100m v o =0.3v ta=?40c 25c 100c fig.1 input voltage vs. output curren t (on characteristics) input voltage : v i (off) (v) output current : io (a) 03 .0 10m 1 2m 5m 1m 200 500 100 20 50 10 2 5 0.5 1.0 1.5 2.0 2.5 v cc =5v ta=100c 25c ?40c fig.2 output current vs. input voltag e (off characteristics) output current : i o (a) dc current gain : g i 1k 500 200 100 50 20 10 5 2 1 100 200 500 1m 2m 5m 10m 20m 50m 100 m v o =5v ta=100c 25c ?40c fig.3 dc current gain vs. output current output current : i o (a) output voltage : v o (on) (v) 100 200 500 1m 2m 5m 10m 20m 50m 100 m 1 500m 200m 100m 50m 20m 10m 5m 2m 1m l o /l i =20 ta=100c 25c ?40c fig.4 output voltage vs. output current
r1120a www.rohm.com ? 2012 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes no copying or reproduction of this document, in part or in whole, is permitted without the consent of rohm co.,ltd. the content specified herein is subject to change for improvement without notice. the content specified herein is for the purpose of introducing rohm's products (hereinafter "products"). if you wish to use any such product, please be sure to refer to the specifications, which can be obtained from rohm upon request. examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when design ing circuits for mass production. great care was taken in ensuring the accuracy of the information specified in this document. however, should you incur any damage arising from any inaccuracy or misprint of such information, rohm shall bear no responsibility for such damage. the technical information specified herein is intended only to show the typical functions of and examples of application circuits for the produc ts. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm and other parties. rohm shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. the products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, commu- nication devices, electronic appliances and amusement devices). the products specified in this document are not designed to be radiation tolerant. while rohm always makes efforts to enhance the quality and reliability of its products, a product may fail or malfunction for a variety of reasons. please be sure to implement in your equipment using the products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any product, such as derating, redundancy, fire control and fail-safe designs. rohm shall bear no responsibility whatsoever for your use of any product outside of the prescribed scope or not in accordance with the instruction manual. the products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel- controller or other safety device). rohm shall bear no responsibility in any way for use of any of the products for the above special purposes. if a product is intended to be used for any such special purpose, please contact a rohm sales representative before purchasing. if you intend to export or ship overseas any product or technology specified herein that may be controlled under the foreign exchange and the foreign trade law, you will be required to obtain a license or permit under the law.
|
